NOTE: You, the customer, are solely responsible for data security. WinBook strongly recommends that you perform a backup of all personal data contained on your system prior to performing this procedure. Warning: WinBook will NOT be held responsible for any data loss incurred during this process.

To complete this procedure you will need the following materials.

• WinBook Windows 95 Boot Disk ver. 2.40
• Microsoft Windows 95 CD
• Microsoft Windows 95 users manual with Product ID

1. Choose the Start button, Shutdown and Restart in Ms-DOS Mode Option.
2. At the DOS prompt Type CD\ and push the Enter key.
3. Type copy c:\windows\command\deltree.exe and press enter.
4. Then Type Deltree C:\Windows and press the Enter.
5. The unit will ask do you want to Delete Windows and all its sub directories Yes/NO Type Y for yes. After the unit returns to a Command Prompt C:\>.
6. Turn off your computer.  Insert your floppy disk drive.
7. Insert the disk labeled WinBook Windows 95 Boot Disk ver. 2.40 and turn on your computer.
8. At the menu choose option number 11.
9. This will reinstall Windows 95.

Set display properties:

1. Choose the Start button, then Settings, next Control Panel.
2. Open Display.
3. Select the Settings tab
4. Change the Screen Area from 640X480 to 800X600 (the Desktop Area will automatically be changed to 800X600)
5. Click the Apply button
6. When asked to change the monitor type click the Yes button
7. Under Models find the Laptop Display Panel (800X600) entry
8. Click the OK button
9. Click OK again
10. Select OK again to keep the new settings.
11. Finally click on the OK button to close the display properties

Install WinBook Modem Driver:

1. Insert the Support Disk into drive A:
2. Click the Start button
3. Select Run from the menu
4. In the Open text box type A:\10.bat and click OK
5. A MS-DOS window will be opened and 10.bat will run. When completed you will see the WinBook Utility menu. Close the window when you see the menu
6. Right click on the My Computer icon
7. Select Properties from the menu
8. Look for the Modem icon and click the + sign next to it
9. Double click on 28.8 Modem
10. Select the Driver tab
11. Click the Update Driver button
12. Select No, select from a list and click Next
13. Highlight the Modem entry and click Next
14. Under manufacturers locate WinBook Computer Corp (NOT WinBook)
15. Highlight WinBook v.34 under Models and click Finish
16. Click the Close button to close modem properties
17. Click Close again to close system properties

Enable PCMCIA support:

1. Right click on the My Computer icon
2. Click on Properties from the menu
3. Click on the Device Manager tab
4. You should see a X through the icon next to Cirrus Logic PCIC compatible PCI to PCMCIA bridge
5. Double click on Cirrus Logic PCIC compatible PCI to PCMCIA bridge
6. Click on the Disable in this hardware profile, This should remove the check mark
7. Click on OK
8. Select the Next icon from the Welcome to the PC Card (PCMCIA) Wizard screen
9. Select the Next icon from the PC Card (PCMCIA) Wizard screen
10. Select the Finish button
11. Select the Yes button to shut down your system now
12. Turn on your system

Your feedback is greatly appreciated. If you have noticed any problems with this tech article, or if you feel that something is not clear enough, please E-mail our Technical Support department by clicking on the link below. Please include the Technical Article Number and the specific area that you feel is inaccurate. Thank you. 
WinBook Tech Article Feedback

Disclaimer: This information is being provided to you as a service from the Technical Support Department of WinBook Computers. It is intended to assist you in the resolution of your technical problems or questions. If you feel uncomfortable implementing any of the information or suggestions contained herein then you should e-mail the WinBook Technical Support Department. WinBook will not be held responsible for any loss of information, data or programming as a result of the use of this TechNote.